Skip to main content

Easiest Way to Connect Raspberry Pi Through SSH Over WiFi

Here is a simple way to connect raspberry pi and ssh into it.

Note: If  you are using pi zero, it is assumed that you have a usb wifi adapter connected through the USB port.
  • Open terminal in boot partition of the SD card.
  • Enable SSH:
    • $ touch ssh
  • Set Wifi Network:
    • $ touch wpa_suplicant.conf
      • ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
network={
    ssid="YOUR_NETWORK_NAME"
    psk="YOUR_PASSWORD"
    key_mgmt=WPA-PSK
}
      • Line 1 is only for Raspbien stretch. Delete it if you are using Jessie.
  • Connect through SSH:
    • Insert SD card and boot.
    • Find the IP address of the Raspberry Pi by accessing the router.
      • e.g. BT uses 192.168.1.254
    • $ ssh pi@xxx.xxx.x.xx
    • Enter default password: raspberry
  • Done!

Comments

Post a Comment

Popular posts from this blog

Getting Used to tmux!

This is a short guide to multiplexing in your terminal! Installation Install  $ sudo apt install tmux launch $ tmux Core Commands Here is a small list of the most useful set of commands. Just remember these and you shall be tmuxing around in no time! Adding panes Add panes vertically ctl + b % Add panes Horizontally ctl + b "  Moving around panes Move to the panes to the right ctl + b <Right> Move to the panes to the left ctl + b <LEFT> Move to the panes to the up ctl + b <UP> Move to the panes to the down ctl + b <DOWN> Closing Window  Close current panes ctl + d Tip!!! You can resize panes by pressing: $ ctl + b + <arrow button> Scroll: $ ctl + b [ press < UP > or < DOWN > Quit $ q  
Post a Comment
Read more

How to Set a Custom Display Resolution on Linux

 Here's how to set a custom display resolution on linux. This guide has been tested on Linux Mint 22 It is a trying to set a display resolution of 1352x878 This also changes the display resolution of a the native display of the laptop ( eDP-1) $ cvt 1352 878 grab the return string  Modeline "1352x878_60.00"   97.50  1352 1432 1568 1784  878 881 891 912 -hsync +vsync $ xrandr --newmode "1352x878_60.00"   97.50  1352 1432 1568 1784  878 881 891 912 -hsync +vsync $ xrandr --addmode eDP-1 "1352x878_60.00" $ xrandr --output eDP-1 --mode "1352x878_60.00"    Enjoy!
Post a Comment
Read more

Installing Qt Cross Compilation Toolchain for Beaglebone Black

This is the guide that I went through to successfully set the environment. If you get stuck on something, feel free to have a look at the references in the bottom most. These are the steps that worked for me so I hope it helps. Just making sure of the dependencies sudo apt-get update sudo apt-get upgrade sudo apt-get install lib32z1 lib32ncurses5 lib32bz2-1.0 libstdc++6:i386 ia32-libs Assuming that you can get access to the root Set up Cross compiler Download and install wget -c https://releases.linaro.org/components/toolchain/binaries/6.4-2018.05/arm-linux-gnueabihf/gcc-linaro-6.4.1-2018.05-x86_64_arm-linux-gnueabihf.tar.xz tar xf gcc-linaro-6.4.1-2018.05-x86_64_arm-linux-gnueabihf.tar.xz export CC=`pwd`/gcc-linaro-6.4.1-2018.05-x86_64_arm-linux-gnueabihf/bin/arm-linux-gnueabihf- Test installation ${CC}gcc --version Download qt source #do this in a directory that is not in your root filesystem, i.e. ~ git clone git://code.qt.io...
Post a Comment
Read more